Induction heater allows you to heat the metal up to redness, without even touching it. The basis of such a heater is a coil in which a high frequency field is created, which acts on a metal object placed inside. High density current is induced in the metal, which causes the metal to heat up.

Repair of built-in power supply and buttons, set-top box satellite tricolor TV. I got into the hands of a non-working set-top box of satellite television tricolor DRS-5003, they presented it to me when it broke, its former owner just bought a new one. The receiver broke down, as my friend said, not silently, as is often the case when, for example, the firmware flies, it dries, or the capacitors swell, the fuse blows, etc.

A drill is a very useful thing for a workshop. Using a drill, you can cut, drill and grind metal blanks. Moreover, this tool is easy to make with your own hands from improvised materials. For example, a drill can be made from an old engine from a bobbin (tape recorder).

To remove bearings from the shaft, as well as for other metal work, a mini hydraulic press is always useful in a home workshop. It can be made from a car jack of 3 tons, a building corner and a profile pipe. The first step is to cut the workpieces from the corner and the profile pipe.

This is perhaps the easiest battery charger you can think of. Such a charge more than once helped me out in difficult situations. It is quite simple to assemble on your own in the absence of a soldering iron and other radio elements. Such a charger can charge the battery of a motorcycle or car in various difficult situations.

In this review, the author shows how to make a wooden floor in a private house with your own hands. There is nothing complicated here, so if you have the necessary tools, every man will cope with this work. In this case, the rough floor from the board is ready. Therefore, it remains only to put the final floor of the board.

You must admit that this is not the most pleasant situation when, in the midst of working on a grinder, a disk suddenly breaks and a nut is tucked. And then unscrew it in the usual way, using the key, is not just difficult, but almost impossible. At least practice shows that in 95% of all cases it happens that way. When you need to quickly replace the disk, then breaking the tool with a chisel or something else, or, for example, disassembling it, trying to remove the naughty nut, is not necessary.

After repairs, scraps of plastic sewer pipes often remain in the house along with bends and semi-bends. So, from the tap you can make a simple wall lamp, which can be placed on the street above the front door. If in a private house a similar element of decor seems inappropriate to you, then it can be "sheltered" in the country.

Often, most people are afraid to unscrew the oblique strainer nut. The fact is that such a filter is usually located immediately after the crane on a riser, and this place is very responsible. Since the mistake made can lead to a flood not only of oneself, but also of neighbors from below. Plus, the supply to the filter can be made of plastic pipes, which will fluctuate greatly with an incorrectly applied force.

In this review, the author shows a rather unusual, but at the same time simple way, how to make a hole in the glass. And you can make not only a round, but also a square or triangular hole (in general, any shape). Holes can be made in any glass, including tempered and automotive, and in any part of the glass, which is very convenient.

When you need to roll out a large number of small round dough cakes with a rolling pin, cooking can turn into a very tedious task. However, in order to facilitate labor, a simple fixture can be made for this. Any man will cope with this task. Of the basic materials for the manufacture of this homemade product, board trim, a wooden block and a furniture hinge will be required.

Sometimes you have to deal with such an unusual situation: after you open the water, the kitchen faucet starts to buzz. Why is this happening and how to fix the problem? In fact, this problem can be solved by any man who at least once encountered installing plumbing. In most cases, the reason is the corrugated eyeliner, which brings water to the mixer itself.